To add an automation device to your system, log into your account on the Frontpoint app and then follow the instructions below based on the device you wish to add:

Outdoor Smart Plug

1. Tap to open the navigation menu.

2. Tap Add Device.

3. Tap Other Z-Wave at the bottom of the device list.

4. Follow the instructions on screen to trigger and add your device to your system.

   • To trigger the Outdoor Smart Plug, make sure it is plugged in and then click the button on the top of the device when prompted.

Indoor Smart Plug

Tap to open the navigation menu.

1. Tap Add Device.

2. Tap Other Z-Wave at the bottom of the device list.

3. Follow the instructions on screen to trigger and add your device to your system.

If a 5-digit pin is requested, you can find the pin (PIN:#####) under the QR code on the side of your Indoor Smart Plug.​

Wireless Light Control

OR1. Tap to open the navigation menu.

1. Tap Add Device.

2. Tap Z-Wave Devicel

3. Follow the instructions on screen to trigger and add your device.

   • To trigger the Wireless Light Control, make sure it is plugged in and then click the button on the top or front of the device, depending on your model when prompted.

Smart Door Lock (Yale)

OR

1. Tap to open the navigation menu.

2. Tap Add Device.

3. Tap Lock and select Touchscreen Deadbolt.

4. Follow the instructions on screen to trigger and add your device.

   • To trigger the Smart Door Lock (Yale), remove the faceplate and use a thin tool to press the pairing button (shown below) on the side of the lock until it beeps twice.

Smart Door Lock (Schlage)

1. Tap to open the navigation menu.

2. Tap Add Device.

3. Tap Lock and select Other Z-Wave Lock.

4. Follow the instructions on screen to trigger and add your device.

   • To trigger the Smart Door Lock (Schlage), follow the steps below:

     1. Press Schlage.

     2. Enter the 6 digit programming code (the programming code can be found on the back of the interior section of the lock, shown in the image below).

   • Press the 0 key on the lock's keypad.

   • If successful, the check mark under the 7 key on the keypad will light up.

Smart Light Bulb

OR

1. Tap to open the navigation menu.

2. Tap Add Device.

3. Tap Lighting and Appliance Control and select Other Z-Wave Light.

4. Follow the instructions on screen to trigger and add your device.

   • To trigger the Smart Light Bulb, make sure it is installed in a device that has power and then turn the bulb ON. If the it is not being recognized, turn the bulb OFF then ON again.

Smart Thermostat

1. Tap to open the navigation menu.

2. Tap Add Device.

3. Tap Thermostat and select T-3000 Smart Thermostat.

4. Follow the instructions on screen to trigger and add your device.

   • To trigger the Smart Thermostat, make sure it is powered-on and then follow the steps below:

     1. Press the Menu button.

     2. Select Settings.

     3. Select Network.

     4. Select Add.

Garage Door Controller

1. Tap to open the navigation menu.

2. Tap Add Device.

3. Tap Other Z-Wave at the bottom of the device list.

4. Follow the instructions on screen to trigger and add your device to your system.

   • To trigger the Garage Door Controller, make sure it is powered-on and then click the button on the side of the device.

Having trouble?

If the automation device is functioning but fails to add to your system, verify the following:

1. The automation device is fully powered either by a wall outlet or with high quality, sufficiently charged batteries.

2. The automation device is within range of the security panel.

_If after verifying the #1 and #2 above the device still fails to add to your system, the automation device needs to be reset. For instructions to reset your automation device, see the step by step guide.